The symptom of the Display Driver Failed to Start bug are rather straightforward. The system freezes frequently, the view flickers, speed may diminish, and similar. Besides, people should receive a message from Notifications Center saying: Display Driver Failed to Start Display Driver failed to start; using Microsoft Bad Display Driver instead. Restart Graphics Driver. If your display driver crashes and fails to restart, you can restart it in. Nvidia driver 384 ran well on Ubuntu 17.04 and 17.10. I switched to Ubuntu 18.04 (clean fresh install) and installed nvidia-driver-396 following this great answer. Then I installed cuda toolkit 9.2 using.run file. It failed to install with and without choosing to install nvidia driver along with it. Fix Failed to Load Hardware Monitor Driver in Windows 10 Tutorial. Commands Shown In Video: bcdedit.exe /set nointegritychecks on bcdedit.exe /set nointegr. Jun 27, 2020.
Visit the Macrium web site Browse our Support Forum
Complete User Guide
Use drivers of the same architecture
Drivers, like any other form of software, have an architecture, either 32 bit (x86) or 64 bit (x64). When trying to load drivers in WinPE, it is essential to have drivers which match the architecture of your WinPE environment. For example, using 32 bit drivers on a 64 bit WinPE could cause load failures.
Drivers not located on accessible disk
Normally, when booting from a RAID controller, be it array or single drive configuration, drivers will need to be loaded in order to access that device. However, as the device will not be visible to WinPE you cannot put drivers on any disk (fixed or optical) which is connected to that controller.
Solution 1 : Make drivers available on accessible media such as a usb device
In order to get round this chicken and egg problem, you will need to place drivers for the device onto a disk which is visible in WinPE, a good choice would be a USB pen drive for this (USB2 recommended unless PE4). The exceptions to this are nVidia RAID and Intel Matrix RAID, as WinPE has built in driver support for these devices. The drivers folder can be copied to another disk using the following method whilst in Windows: If you have a local non-RAID disk 'e:' then from a command prompt type: xcopy /e c:bootmacriumdrivers* e:bootmacriumdrivers if 'e:' is a removable (flash) drive, then use the following command: xcopy /e c:bootmacriumdrivers* e:drivers Note: The '/e' switch means recursive copy and is not to be confused with the drive letter 'e:'. If 'e:' is present during the boot menu load then the drivers will be loaded.
Solution 2 : Add drivers to the PE Image
You must either be running Reflect v5.2 or later and have created an 'Auto-built Windows PE' rescue CD (WAIK or WADK for Windows 8). Follow all the steps below:
1.Take the 'Windows PE' rescue CD option in the rescue CD wizard. Just click 'Next' and be patient while the integration completes.
3. Once the integration is finished cancel the rescue media wizard on the final Wizard page.
4.Download and run 'inject.exe' from here:
This will automatically inject the drivers into the windows image file (WIM) and will take a few minutes.
5. Once completed, take the rescue media build wizard again, click through to the final page and create your rescue media. Drivers will be integrated and you should have no problems booting with the CD and recognizing your local RAID volumes or USB 3.0 host controllers (PE3.1).
Note: If you re-integrate the rescue media WIM by clicking the 'Re-Build' button on the final Wizard page, or if an update to Windows PE is made available then you must follow this procedure again to add drivers into the newly created WIM file.
If you still have problems then email the file 'c:waiklog.txt' and an explanation of your issue to support (at) macrium.com so we can investigate further.
Driver location load order
Macrium Reflect will load drivers based on the existence of the file macrium.oem, the following locations will be checked in sequence and if the file macrium.oem is found then driver loading will commence from that point. Subsequent locations will not be checked for drivers.
Removeable media (such as USB pen drives). The file (macrium.oem) must reside in the Drivers folder on the root of the media.
CD=ROM/DVD-ROM drives. The file (macrium.oem) must reside on the Drivers folder on the root of the media.
Local fixed hard disks. The file must reside on the BootMacriumDrivers folder on the root of the local hard disk.
Office tab for mac. Please note that in Windows, the drivers folder that's loaded when WinPE boots can be located in c:BootMacriumDrivers. Once USB/CD-ROM/DVD-ROM rescue is created this folder will be Drivers on the root of the respective rescue media.
Missing support files
Display Driver Failed To Load File
On 64 bit WinPE systems, most drivers will require a supporting security catalog and in some instances, DLL files. If running a 64 bit Windows Vista system or later, Macrium Reflect will take care of this for you when building the rescue media. However, if on an XP or 2003 Server operating system you will need to make sure you provide a driver package that contains a security catalog and any supporting DLL files when using the Update Driver feature in the Create Rescue Media wizard.
Windows 10 users often complain about display issues after upgrading to Windows 10. If you have an NVIDIA Graphics Chip installed and you are seeing some errors, then these solutions might help you to resolve the issue.
Display Driver Fail Windows 10
Error message – “NVIDIA Installer failed”
This is a common issue reported by many users following an upgrade to Windows 10. When you upgrade to Windows 10, the Windows update tries to download and install graphics drivers in the background. Sometimes this process takes 5-10 minutes or even longer. If you try installing NVIDIA Graphics Drivers immediately, you will most likely get an error which says NVIDIA installer failed.
Solution 1 to NVIDIA installer failed issue
To resolve this issue, let the Windows 10 system sit idle for 15-20 minutes to ensure the Windows Update has completed the downloading and installation processes. After waiting for 15-20 minutes, reboot the system. Once the system is up again, install the NVIDIA Driver by following the steps set out below:
In the Installation options screen, select Custom
Click Next
On the next screen, check the box “Perform a clean installation”
Click Next
Follow on-screen instructions to complete the installation
Reboot the system
If the drivers are not successfully installed, try Solution 2 below.
Solution 2 to NVIDIA installer failed issue
Turn off your antivirus and firewall
Some antivirus tools are known to block files during the NVIDIA Driver installation. Some Comodo antivirus users have reported NVIDIA Driver failed issues. If you are running any firewall and antivirus software, turn it off before starting the installation process.
Turn off the antivirus program and also kill the remaining processes related to them. You can do this by killing the antivirus processes in the Task Manager. Follow the steps below to turn off antivirus and firewall temporarily:
Press Ctrl+Alt+Delete
Click Task Manager
Go to the Processes tab
Look for any processes related to antivirus and kill each of them – Click on each process and select End Task to kill the process
Reboot your PC
Try installing the NVIDIA Driver. Select Custom and check the box “Perform clean installation” during installation
If you get the NVIDIA installation error again, follow the steps given in Solution 3
Solution 3 to NVIDIA installer failed issue
Go to Task Manager
Go to the Processes tab to end any NVIDIA processes
You also need to delete some NVIDIA installation related files
To delete any NVIDIA related files, you need to log in as administrator